Microchip Technology
Obraz może przedstawiać obraz.
Szczegóły produktu można znaleźć w specyfikacjach.
MCP2200T-I/SS
Pokaż szczegóły Arkusze danych

MCP2200T-I/SS

Product Overview

Category

The MCP2200T-I/SS belongs to the category of USB-to-UART serial converters.

Use

This product is primarily used for converting Universal Serial Bus (USB) signals to UART (Universal Asynchronous Receiver-Transmitter) signals. It enables communication between a computer and devices that use UART for data transfer.

Characteristics

  • USB-to-UART conversion capability
  • Small form factor
  • Low power consumption
  • High data transfer rate
  • Support for various operating systems

Package

The MCP2200T-I/SS is available in a SSOP-20 package, which ensures easy integration into electronic circuits.

Essence

The essence of the MCP2200T-I/SS lies in its ability to bridge the gap between USB and UART interfaces, facilitating seamless communication between computers and UART-based devices.

Packaging/Quantity

This product is typically packaged in reels or tubes, with a quantity of 250 units per reel/tube.

Specifications

  • Supply Voltage: 3.3V
  • Data Transfer Rate: Up to 1 Mbps
  • Operating Temperature Range: -40°C to +85°C
  • Interface: USB 2.0 Full-Speed
  • GPIO Pins: 9
  • UART Pins: 4

Detailed Pin Configuration

  1. VDD - Power supply voltage
  2. D- - USB data minus line
  3. D+ - USB data plus line
  4. GND - Ground
  5. GP0 - General-purpose I/O pin 0
  6. GP1 - General-purpose I/O pin 1
  7. GP2 - General-purpose I/O pin 2
  8. GP3 - General-purpose I/O pin 3
  9. GP4 - General-purpose I/O pin 4
  10. GP5 - General-purpose I/O pin 5
  11. GP6 - General-purpose I/O pin 6
  12. GP7 - General-purpose I/O pin 7
  13. TX - UART transmit pin
  14. RX - UART receive pin
  15. RTS - Request to Send pin
  16. CTS - Clear to Send pin
  17. RI - Ring Indicator pin
  18. DTR - Data Terminal Ready pin
  19. DCD - Data Carrier Detect pin
  20. GND - Ground

Functional Features

  • USB-to-UART conversion: Enables communication between USB and UART interfaces.
  • GPIO Pins: Provides general-purpose input/output pins for additional functionality.
  • Flow Control: Supports hardware flow control using RTS (Request to Send) and CTS (Clear to Send) pins.
  • Status Indicators: Includes LEDs to indicate power and data transfer status.

Advantages and Disadvantages

Advantages

  • Easy integration into existing systems
  • High data transfer rate
  • Low power consumption
  • Support for various operating systems
  • Compact form factor

Disadvantages

  • Limited number of GPIO pins
  • Requires external components for complete functionality

Working Principles

The MCP2200T-I/SS operates by converting USB signals received from a computer into UART signals compatible with UART-based devices. It utilizes an internal USB transceiver and UART interface to facilitate bidirectional data transfer. The device is controlled through software commands sent via the USB interface.

Detailed Application Field Plans

The MCP2200T-I/SS finds applications in various fields, including but not limited to: 1. Industrial automation 2. Embedded systems 3. Internet of Things (IoT) devices 4. Robotics 5. Consumer electronics

Detailed and Complete Alternative Models

  1. CP2102N-A01-GQFN28: USB-to-UART bridge controller with similar features and package.
  2. FT232RL: USB-to-UART converter with additional features like bit-bang mode and EEPROM support.
  3. PL2303HXD: USB-to-UART bridge controller with built-in RS-232 level shifter.

These alternative models offer similar functionality to the MCP2200T-I/SS and can be considered based on specific requirements and compatibility.

Word count: 531 words

Wymień 10 typowych pytań i odpowiedzi związanych z zastosowaniem MCP2200T-I/SS w rozwiązaniach technicznych

  1. Question: What is the maximum baud rate supported by MCP2200T-I/SS?
    Answer: The maximum baud rate supported by MCP2200T-I/SS is 115200 bps.

  2. Question: Can MCP2200T-I/SS be used for USB to UART conversion?
    Answer: Yes, MCP2200T-I/SS can be used for USB to UART conversion.

  3. Question: What are the operating voltage and current requirements for MCP2200T-I/SS?
    Answer: The operating voltage range for MCP2200T-I/SS is 3.3V to 5.25V, with a typical current consumption of 25 mA.

  4. Question: Does MCP2200T-I/SS support I2C communication?
    Answer: Yes, MCP2200T-I/SS supports I2C communication.

  5. Question: Is there a software development kit (SDK) available for MCP2200T-I/SS?
    Answer: Yes, there is an SDK available for MCP2200T-I/SS, which includes drivers and example code for various platforms.

  6. Question: Can MCP2200T-I/SS be used for interfacing with RS-232 devices?
    Answer: Yes, MCP2200T-I/SS can be used for interfacing with RS-232 devices using appropriate level shifters.

  7. Question: What is the maximum number of GPIO pins available on MCP2200T-I/SS?
    Answer: MCP2200T-I/SS provides 8 general-purpose I/O pins.

  8. Question: Does MCP2200T-I/SS support USB suspend mode?
    Answer: Yes, MCP2200T-I/SS supports USB suspend mode to minimize power consumption.

  9. Question: Can MCP2200T-I/SS be used in industrial temperature range applications?
    Answer: Yes, MCP2200T-I/SS is designed to operate in industrial temperature range (-40°C to +85°C).

  10. Question: Are there any known compatibility issues with specific operating systems?
    Answer: MCP2200T-I/SS is compatible with most major operating systems, but it's recommended to check the latest driver availability for specific OS versions.